蛋托模具47多少錢一套

Ⅰ 生產一個蛋托的利潤是多少

蛋托是靠生產量來賺利潤的，綜合國內生產分析，正常利潤在5分左右，還要看當地原材料廢紙的價格，合理科學管理，不過這個行業利潤還是可以的！

Ⅱ 請問紙托(雞蛋托).和泡沫比較,誰的價格高啊.

紙托更環保一些，支持紙托。

Ⅲ 首飾模具一套大概多少錢/.

一般首飾模具開出來都是需要再加工的，首飾模具的話這模具比較粗糙預計開模費在1000多點

Ⅳ 雞蛋的蛋托是怎麼做的，什麼工藝

1、根據要求或樣品規格，首先製作好雞蛋托吸塑模具，一般條件下都是利用石膏製作吸塑包裝模具，讓其自然乾燥完全或是烘乾，然後根據產品表面凸凹具體情況，在不影響產品包裝模樣的低凹處鑽許多小孔。

2、接下來就是將雞蛋包裝盒模具處理乾燥完全後，將雞蛋托模具裝入真空室上層鐵板上，然後根據雞蛋托模具大小，將塑料片載成適用規格尺寸，然後將此片材放入加熱木櫃內，使其完全固定好，再將木櫃連同塑料片材置恆溫爐上進行軟化處理。

3、第三步是比較關鍵的，將軟化處理好的塑料片連同木櫃，置於真空室中，開動吸氣開關，將真空室內空氣吸抽干凈，待塑料片冷卻後，即得到與模具相同的凹型雞蛋托。 然後就是雞蛋包裝盒整理；將生產出來的雞蛋托進行修邊整理後，才是成品的雞蛋包裝盒，這樣就可以出廠進行銷售了。

(4)蛋托模具47多少錢一套擴展閱讀：

分類

1、紙漿蛋托

紙漿蛋托多是採用再生紙紙漿經成型機具壓制而成，因其製作工藝簡單，造價低廉，無環境污染，被稱為「綠色」包裝，是日常最常見的一種蛋托。

2、塑料蛋托

塑料蛋托採用塑料作為材質，可是製作出五顏六色、造型精美的蛋托。因其成本較高，一般在高檔超市用的較多。

3、單體蛋托

單體蛋托一般用於家庭或西餐店，具有造型可愛、使用方便的特點，可有效防止雞蛋從餐桌上滾落。是時尚家居的備選小餐具。

4、盤裝蛋托

盤裝蛋托根據大小不同一盤可裝幾十個蛋，也是用的較多的雞蛋包裝工具。

Ⅳ 英文翻譯：蛋托模具使用說明

Removing and cleaning demolition sites and ready 1 work, mould disassembly, cleaning, repair and maintenance should be in special places. The site should be sufficiently far from the " rough " proction area. The workplace should be kept clean, and the pad to the corrugated cardboard or rubber plate. 2, the work area shall have a variety of tools ( screwdriver, wrench ), soft Guapian ( brass, soft aluminum procts ), cleaning and polishing materials, as there may be extrusion die preheating device. 3, extrusion die should take the advantage of heat removing, must work quickly to avoid premature cooling. When the die is extrusion machine, the mold is heated to a temperature higher than the proction when the temperature of 20 degrees Celsius, then stop heating disconnect all power, rapid release on the side plate fastening Ross, removing the lower sides of side plates. In the mold is still at the high temperature state, loosen the upper and lower mold body of the fastening screw, and the host connection screw. After using the crane to hang the upper die body is placed in close proximity to the work area, and quickly clean, a lower die body. Clear channel must use soft wiper blade or a copper brush, in the flow passage of any resial resin need to clean up, can use paraffin or solvent cleaning, do not use a steel appliances. In 4, the mold cooling after the clean-up: mold flow and seal rings should use soft blade, thin flat stone and metallographic sandpaper to clean and polish the surface with a soft mold other, a scraper and 240# above the fine sandpaper to clean, each equipped with contact and non-contact surface should be clean and Yu Shu. In 5, when the work has been completed, it can be further assembly. The assembly should be checked before the finish mold runner, must remove smaller small scratches, relatively strict injury should be sent back to the factory repair. 6, in the extrusion die formally before the assembly, preferably the channel is coated with thin layer of organic silicone grease, such as molybdenum ore or graphite grease, to ensure that the mold ring operation and disassembly are very convenient. In 7, the assembly should be paid attention to when assembling size to meet the requirements of assembly, the right, in the mold in the state of cooling when tightening the screw is connected, when the die and extrusion machine links stability and heated to operating temperature should be tightened again after correction of each connecting screws.