⑴ 模具專業英語翻譯。（高分100分）有行家幫幫忙。謝謝
Strippers
There are tow types of strippers: fixed or spring-operated.The primary function of either type is to strip the workpiece from a cutting or noncutting punch or die.A stripper that forces a part out of a die may also be called a knockout, an inside stripper, or an ejector . Besides its primary function, a stripper may alwo hold down or clamp, posirion ,or guide the sheet, strip , or workpiece.
剝離器（脫模機）
有兩種類型的剝離器: 固定的和彈簧驅動的．對於這兩種類型而言，它們的主要功能都是將工件從剪切或者非剪切沖頭（沖栽模）上剝離．促使沖栽模的一部分與其自身分離的剝離器亦叫做脫模裝置，內置剝離器或者脫模器（推出器）．此外，剝離器還起著固定裝置，薄板，剝片和工件的作用．
The stripper is usually the same width and length as the die block ,In simpler dies, the stripper may be fastened with the same screws and dowels that fasten the die block ,and the screwheadw will be counterbored into the stripper ,In more compex tools and with sectional die blocks, the die block screws will usually be inverted , and the stripper fastener will be independent .
剝離器通常與沖栽模塊等長等寬．在一些構造更為簡單的沖栽模中，剝離器也許會和模塊共用同樣的螺絲和暗榫固定，同時螺絲釘的頭部將鑽埋於剝離器內．對於一些較為復雜的工具和那些組合式沖栽模而言，螺絲釘通常都是倒置的，而且剝離器的扣件都是獨立的．
The stripper thickness must be sufficient to withstand the force required to strip the strip the stock from the punch , plus whatever is required for the stock strip channel. Except for very heavy tools or large blank areas, thethickness required for screwhead counterbores ,in the range of 3/8」 to 5/8」(9.5mm—16mm),will be sufficient.
剝離器要有足夠的壁寬以經受將坯料從沖壓機上剝離所需要的壓力以及任何沖模通道所需的力． 除非是重量級的工具或者有相當大的接頭部分，通常對於螺絲頭的平孔鑽的寬厚度應該達到9．5MM至16MM．
The height of the stock strip channel should be at least 1.5 times the stock thickness . This height should be increased if the stock is to be lifted over a fixed pin stop .The Channel widthshould be the width of the stock strip, plus adequate clearance to allow for variations in the width of the strip cut.
坯料剝離通道的高度應當至少是坯料厚度的1．5倍．如果坯料的高度被提升至超過了固定的擋料銷（定位銷），這個高度就應當相應地增加．通道的寬度應當與坯料條的寬度相等，同時要留出足夠的邊隙以應對不同寬度的剪切樣條．
Choice of the methods of applying springs to stripper plates depends on the required pressure, space limitations, shape of the die, nature of the work ,and proction requirements . Figure 9-12 presents a number of such methods.
如果要將彈簧應用到分餾柱塔板上，那麼你必須考慮其所需的壓力，空間的尺度限制，模具的形狀，工件的性質與質地以及生產規格的要求．（這些因素都將影響彈簧的選擇與應用方式）
圖9－12展示了一些相應的應用方式．
P.S. 鑒於學的不是相關的專業,因此一些專業詞彙的翻譯未免有許偏差,但從語法來看大致應該是這個意思,你可以結合自己的專業知識在這個基礎上再作一番修正.
⑵ 模具專業英語
Mold consists of three basic components, namely, dynamic simulation part of the floating cavity plate and fixed template. Push plate aperture to be compared with cores of large-diameter slightly larger number of threads to prevent thread appears scratches. Assembly organizations from push plate, push the semi-fixed panels and ejector rod composed of injection molding machines. Floating cavity plate distance from the maximum movement limit control of nails or similar devices. Principles of injection molding and casting are very similar. Resin material into a rotating screw, you should enter off three zones: the feeding area, compaction area and the plasticizing zone. Gate is the entrance of molten plastic into the cavity shunt wall must be smooth, in order to prevent melt flow generated parting surface of the shape of the resistance depends entirely on the shape of the shrinking role of the plastic to make plastic parts ejection difficulties. Injection cooling, the contraction depends on the plastic parts melt molding processes.
⑶ 模具專業英語翻譯幫幫忙啊，急急急！！！
the forming process and die design of tooth glass
Abstract
The main topics wereinjection mold design of tooth glass, and introced the plastic forming process, as well as the process of injection molding, injection molding machine also carried out on a number of brief. Plastic procts through the process of analysis to determine the number of the cavity, the choice of injection molding machine, as well as the structural design of mold. The structural design of mold include: the design of gating system, forming part design, design-oriented, type design side, Demoulding design, cooling design and exhaust system design. The design is a two-cavity three-plate mold. Due to the special shapeof tooth glass, can not be directly Demoulding need to set up the side of sub-type institutions, the set of mold is guided through the inclined side column type, the various parts of the mold parts to the design and calculation, and the work of die principle and the working process, as well as the use and maintenance of molds are also described, and given the design process in detail and assembly drawings.
⑷ 模具專業英語翻譯~~~~~~~~~
注塑機，這是一般水平，評分是根據能力的模具和夾緊力對模具，它在大多數機器是一個幾百tons.typical射出零件是杯盤器皿，各種電器及通訊組件，玩具及管件。
在反應注射成型（ RIM ）所夾雜的兩個或兩個以上的接觸過程中，被迫在高壓下進入模具cavity.chemical反應發生在模具迅速和聚合物solidifies.various纖維如玻璃，石墨，或硼可能也可以用來加強materials.structural泡沫也產生類似的方法（和擠壓）利用惰性氣體（通常為氮氣）和樹脂mixture.the產品構成的一個硬性蜂窩（非公開細胞）的結構與連續性固皮膚作為留言Muchas 0.080英寸（ 2毫米） ，在thickness.there有幾種方法，形成結構性的泡沫密度減少了四成之多，從固體structure.because剛度成正比第三力量厚度的一部分，為同樣重量的使用材料，蜂窩結構更為嚴厲的比硬塑料或金屬。
模具環，一般的拋光金屬，壓力和溫度涉及low.major申請汽車保險杠和擋泥板，熱絕緣體，為冰箱和冰櫃，並為加勁結構組件。
⑸ 模具專業英語短文和翻譯
各種模具常用成形方式
accurate die casting 精密壓鑄 powder forming 粉末成形 calendaring molding 壓延成形 powder metal forging 粉末鍛造 cold chamber die casting 冷式壓鑄 precision forging 精密鍛造 cold forging 冷鍛 press forging 沖鍛
compacting molding 粉末壓出成形 rocking die forging 搖動鍛造 compound molding 復合成形 rotary forging 回轉鍛造 compression molding 壓縮成形 rotational molding 離心成形 dip mold 浸漬成形 rubber molding 橡膠成形 encapsulation molding 注入成形 sand mold casting 砂模鑄造 extrusion molding 擠出成形 shell casting 殼模鑄造 foam forming 發泡成形 sinter forging 燒結鍛造 forging roll 軋鍛 six sides forging 六面鍛造 gravity casting 重力鑄造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting 高壓鑄造 hot chamber die casting 熱室壓鑄 swaging 擠鍛
hot forging 熱鍛 transfer molding 轉送成形 injection molding 射出成形 warm forging 溫鍛
investment casting 精密鑄造 matched die method 對模成形法 laminating method 被覆淋膜成形 low pressure casting 低壓鑄造
lost wax casting 脫蠟鑄造 matched mould thermal forming 對模熱成形模
各式模具分類用語
bismuth mold 鉍鑄模 landed plunger mold 有肩柱塞式模具 burnishing die 擠光模 landed positive mold 有肩全壓式模具 button die 鑲入式圓形凹模 loading shoe mold 料套式模具 center-gated mold 中心澆口式模具 loose detail mold 活零件模具 chill mold 冷硬用鑄模 loose mold 活動式模具 clod hobbing 冷擠壓制模 louvering die 百葉窗沖切模 composite dies 復合模具 manifold die 分歧管模具 counter punch 反擊模 molar mold 組合式模具 double stack mold 雙層模具 multi-cavity mold 多模穴模具 electroformed mold 電鑄成形模 multi-gate mold 復式澆口模具 expander die 擴徑模 offswt bending die 雙折冷彎模具 extrusion die 擠出模 palletizing die 疊層模 family mold 反套製品模具 plaster mold 石膏模
blank through dies 漏件式落料模 porous mold 通氣性模具 plicated cavity plate 復板模 positive mold 全壓式模具 fantail die 扇尾形模具 pressure die 壓緊模 fishtail die 魚尾形模具 profile die 輪廓模 flash mold 溢料式模具 progressive die 順序模
gypsum mold 石膏鑄模 protable mold 手提式模具 hot-runner mold 熱流道模具 prototype mold 雛形試驗模具 ingot mold 鋼錠模 punching die 落料模
lancing die 切口模 raising(embossing) 壓花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 無流道冷料模具 sectional die 對合模具 segment mold 組合模 semi-positive mold 半全壓式模具 shaper 定型模套 single cavity mold 單腔模具 solid forging die 整體鍛模 split forging die 拼合鍛模
split mold 雙並式模具 sprueless mold 無注道殘料模具
var script = document.createElement('script'); script.src = 'http://static.pay..com/resource/chuan/ns.js'; document.body.appendChild(script);
2
squeezing die 擠壓模 stretch form die 拉伸成形模 sweeping mold 帄刮鑄模 swing die 振動模具 three plates mold 三片式模具 trimming die 切邊模 unit mold 單元式模具 universal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 軛型模
模具廠常用之標准零配件
air vent vale 通氣閥 anchor pin 錨梢 angular pin 角梢 baffle 調節阻板 angular pin 傾斜梢 baffle plate 折流檔板 ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑塊 binder plate 壓板
blank holder 防皺壓板 blanking die 落料沖頭 bolster 上下模板 bottom board 澆注底板 bolster 墊板 bottom plate 下固定板 bracket 扥架 bumper block 緩沖塊 buster 堵口 casting ladle 澆注包 casting lug 鑄耳 cavity 模穴(模仁) cavity retainer plate 模穴扥板 center pin 中心梢 clamping block 鎖定塊 coil spring 螺旋彈簧 cold punched nut 冷沖螺母 cooling spiral 螺旋冷卻栓 core 心型 core pin 心型梢 cotter 開口梢 cross 十字接頭 cushion pin 緩沖梢 diaphragm gate 盤形澆口 die approach 模頭料道 die bed 型底 die block 塊形模體 die body 鑄模座 die bush 合模襯套 die button 沖模母模
die clamper 夾模器 die fastener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 沖模板 die set 沖壓模座 direct gate 直接澆口 dog chuck 爪牙夾頭 dowel 定位梢 dowel hole 導套孔 dowel pin 合模梢 dozzle 輔助澆口 dowel pin 定位梢 draft 拔模錐度 draw bead 張力調整桿 drive bearing 傳動軸承 ejection pad 頂出襯墊 ejector 脫模器
ejector guide pin 頂出導梢 ejector leader busher 頂出導梢襯套 ejector pad 頂出墊 ejector pin 頂出梢 ejector plate 頂出板 ejector rod 頂出桿 ejector sleeve 頂出襯套 ejector valve 頂出閥 eye bolt 環首螺栓 filling core 椿入蕊 film gate 薄膜形澆口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圓形模板 fixed bolster plate 固定側模板 flanged pin 帶擊緣銷 flash gate 毛邊形澆口 flask 上箱 floating punch 浮動沖頭 gate 澆口
gate land 澆口面 gib 凹形拉緊銷 goose neck 鵝頸管 guide bushing 引導襯套 guide pin 導梢 guide post 引導柱 guide plate 導板 guide rail 導軌 head punch 頂鐓沖頭 headless punch 直柄沖頭 heavily tapered solid 整體模蕊盒 hose nippler 管接頭
⑹ 模具專業英語翻譯 十萬火急
壓鑄模具
壓力壓鑄模是大會的材料，主要是有色金屬，每個發揮了參與的機制運作的條件下迅速變化的溫度，如熔融金屬注射壓力下，然後立即冷卻。一些地區的死只是作為控股要素;其他國家，如模具刀片和核心，必須經受住的影響和高溫熔化金屬。該機制的噴射器和移動核心工作順利進行，必須在不斷變化的溫度死亡。部分作為軸承是不是有色金屬，如磷青銅或鋼鐵表面氮化物，給予或其他治療抵抗磨損。
插入模具生產形狀的鑄件，必須准確地加工和熱處理，提供最佳的力學性能在高溫下。大多數壓鑄模具和自動操作，而這會導致生產率高時，對延誤，成本也相應高故障。在過去十年的製造模具已被徹底改變了復雜的方法，從改善引發的侵蝕，以電腦控制的模具製造。除其他努力，科學研究理事會正在支持一個大規模的研究方案，包括模具熱處理及表面塗層，計算機輔助模具設計，特殊的加工工藝和經濟學的模具製造。
一個晶元可以包含10個或更多不同的鋼加一些有色金屬和特殊耐熱合金。數字14-1和14-2說明schematically裸片其中典型的各個組成部分，其中每一項涉及設計，工程和冶金問題。
⑺ 模具專業英語術語
Designer - 設計師。
Assembly drawing - 模具組裝圖。
Mold layout - 模具結構圖。
2D proct drawing - 2D產品圖。
3D proct data - 3D產品數據。
Part drawing - 散件圖。
Insert molding - 鑲件模。
2 color mold / Double injection tool - 雙色模。
Hydraulic system - 油/水壓系統。
Parting line - 分模線。
⑻ 在模具專業術語中，英文縮寫CAV、COR是哪些英文單詞的縮寫中文意思又是是什麼
cavity有型腔(前模，母模)的意思，縮寫為CAV
core後模的意思縮寫為COR
⑼ 模具方面的專業英語翻譯：水口過長，披鋒，氣紋，夾線，積油，少油，飛油，拉絲，超壓線有油漆，無明顯段
Runner is too longer, flashes, flow mark, welding line, oid st, brush finish, extend line painted, no obvious step.
⑽ 模具專業英語翻譯
In this passage, a reliable and practical sample moulding is introced. Firstly calculate the overall dimension of workpiece acc workpice drawing, then locate the center pressure point. Draw the layout in consideration of material utilization. Analyse workpiece profile and specific dimensions and punch with compound moulding. It's high of efficiency and simple in proction. With all parameters done, analysis on the assembling of the moulds and requirement of main parts design and assembling was made. Besides guide book on designwork, assembling drw. of mouldings, nonstandard parts drawings, machining charts, processing cards and nonstandard parts machining cards are also included.