『壹』 求助模具英语翻译
什么逼空啊? 你要说避开? 间隙? 让位?
避开 = clearance
间隙= gap
让位 = offside
封胶 plastic sealing
镶件 insert
会破坏运水 will break the cooling pipe
其他你自己凑合一下吧
『贰』 求英语翻译：模具，冲压，消声器总装三位一体，三个部分即可协同发展，又可彼此独立运作。
The final assembly of a mould, a stanping and a muffler is three-in-one, and the three parts can not only develop themself synergistically but also work Independently.
『叁』 模具专业英语翻译。（高分100分）有行家帮帮忙。谢谢
Strippers
There are tow types of strippers: fixed or spring-operated.The primary function of either type is to strip the workpiece from a cutting or noncutting punch or die.A stripper that forces a part out of a die may also be called a knockout, an inside stripper, or an ejector . Besides its primary function, a stripper may alwo hold down or clamp, posirion ,or guide the sheet, strip , or workpiece.
剥离器（脱模机）
有两种类型的剥离器: 固定的和弹簧驱动的．对于这两种类型而言，它们的主要功能都是将工件从剪切或者非剪切冲头（冲栽模）上剥离．促使冲栽模的一部分与其自身分离的剥离器亦叫做脱模装置，内置剥离器或者脱模器（推出器）．此外，剥离器还起着固定装置，薄板，剥片和工件的作用．
The stripper is usually the same width and length as the die block ,In simpler dies, the stripper may be fastened with the same screws and dowels that fasten the die block ,and the screwheadw will be counterbored into the stripper ,In more compex tools and with sectional die blocks, the die block screws will usually be inverted , and the stripper fastener will be independent .
剥离器通常与冲栽模块等长等宽．在一些构造更为简单的冲栽模中，剥离器也许会和模块共用同样的螺丝和暗榫固定，同时螺丝钉的头部将钻埋于剥离器内．对于一些较为复杂的工具和那些组合式冲栽模而言，螺丝钉通常都是倒置的，而且剥离器的扣件都是独立的．
The stripper thickness must be sufficient to withstand the force required to strip the strip the stock from the punch , plus whatever is required for the stock strip channel. Except for very heavy tools or large blank areas, thethickness required for screwhead counterbores ,in the range of 3/8” to 5/8”(9.5mm—16mm),will be sufficient.
剥离器要有足够的壁宽以经受将坯料从冲压机上剥离所需要的压力以及任何冲模通道所需的力． 除非是重量级的工具或者有相当大的接头部分，通常对于螺丝头的平孔钻的宽厚度应该达到9．5MM至16MM．
The height of the stock strip channel should be at least 1.5 times the stock thickness . This height should be increased if the stock is to be lifted over a fixed pin stop .The Channel widthshould be the width of the stock strip, plus adequate clearance to allow for variations in the width of the strip cut.
坯料剥离通道的高度应当至少是坯料厚度的1．5倍．如果坯料的高度被提升至超过了固定的挡料销（定位销），这个高度就应当相应地增加．通道的宽度应当与坯料条的宽度相等，同时要留出足够的边隙以应对不同宽度的剪切样条．
Choice of the methods of applying springs to stripper plates depends on the required pressure, space limitations, shape of the die, nature of the work ,and proction requirements . Figure 9-12 presents a number of such methods.
如果要将弹簧应用到分馏柱塔板上，那么你必须考虑其所需的压力，空间的尺度限制，模具的形状，工件的性质与质地以及生产规格的要求．（这些因素都将影响弹簧的选择与应用方式）
图9－12展示了一些相应的应用方式．
P.S. 鉴于学的不是相关的专业,因此一些专业词汇的翻译未免有许偏差,但从语法来看大致应该是这个意思,你可以结合自己的专业知识在这个基础上再作一番修正.
『肆』 麻烦帮忙翻译 模具相关英文,在线等......谢谢....
注塑模具组Injection mold set
冲压模具组Die Group
挤出模具组Extrusion Tooling Group
抛光组(省模组)Polishing group (province Mole)
机械加工组Machining Group
线切割组 Wire Group
『伍』 英语模具翻译
mould
『陆』 模具类英文，请高手帮忙翻译，多谢!
工厂的工人要穿干净的衣服，工厂必须每天提供干净的工作服，这是基础工作。工人要能按程序的用杀菌液体肥皂和水洗手（ regularly 这里我翻译为按程序可能不太准确，你可以根据上下文找个更合适的词语），工厂要有烘干设备以保证工人返回工作岗位时，手是完全干的。
所有的原材料和其他材料要被包装和存储在密封的地方以避免灰尘的污染。包装好的材料必须存储在距离地板5"/12cm 的木质货架上，使之空气可以充分循环。包好的材料不能碰到墙面，天花板或地板。
人工翻译，希望对你有帮助
『柒』 模具英语翻译，请各位模具高手帮忙翻译一下
1, the mold, installed under the top out of reset, open the film-mode-locked
2, open mold, then water, trip switch, check the top of the reset
3, mold, injection, cooling
4, before the mold core pulling out of the fuel tank
5, open mold, the top out pickup
6, Die
7, the fuel tank before the reset mode
8, the 50-60mm mode, the motor sports, spin out
『捌』 高分求模具英文翻译
No mold line of spindles spinning plastic mold design
The nil-ray tube spindles spinning plastic injection mold design, the key is to die with the ramp-pumping device and to accurately determine the direction of mold and mold guarantee Line is not in the external surface of the tubes. For purposes consider that it is used for winding yarn, which calls for the tubes outer surface smooth enough, This article solve design problems to provide an explanation. And pieces of plastic materials, the quality of analysis and volume calculation, a reasonable selection of injection molding machinery, as well as various parameters of the check, design a reasonable, affordable, suitable plastic injection mold.
Injection Mold; Pumped-ramp; No mold line