『壹』 英文翻译：蛋托模具使用说明
Removing and cleaning demolition sites and ready 1 work, mould disassembly, cleaning, repair and maintenance should be in special places. The site should be sufficiently far from the " rough " proction area. The workplace should be kept clean, and the pad to the corrugated cardboard or rubber plate. 2, the work area shall have a variety of tools ( screwdriver, wrench ), soft Guapian ( brass, soft aluminum procts ), cleaning and polishing materials, as there may be extrusion die preheating device. 3, extrusion die should take the advantage of heat removing, must work quickly to avoid premature cooling. When the die is extrusion machine, the mold is heated to a temperature higher than the proction when the temperature of 20 degrees Celsius, then stop heating disconnect all power, rapid release on the side plate fastening Ross, removing the lower sides of side plates. In the mold is still at the high temperature state, loosen the upper and lower mold body of the fastening screw, and the host connection screw. After using the crane to hang the upper die body is placed in close proximity to the work area, and quickly clean, a lower die body. Clear channel must use soft wiper blade or a copper brush, in the flow passage of any resial resin need to clean up, can use paraffin or solvent cleaning, do not use a steel appliances. In 4, the mold cooling after the clean-up: mold flow and seal rings should use soft blade, thin flat stone and metallographic sandpaper to clean and polish the surface with a soft mold other, a scraper and 240# above the fine sandpaper to clean, each equipped with contact and non-contact surface should be clean and Yu Shu. In 5, when the work has been completed, it can be further assembly. The assembly should be checked before the finish mold runner, must remove smaller small scratches, relatively strict injury should be sent back to the factory repair. 6, in the extrusion die formally before the assembly, preferably the channel is coated with thin layer of organic silicone grease, such as molybdenum ore or graphite grease, to ensure that the mold ring operation and disassembly are very convenient. In 7, the assembly should be paid attention to when assembling size to meet the requirements of assembly, the right, in the mold in the state of cooling when tightening the screw is connected, when the die and extrusion machine links stability and heated to operating temperature should be tightened again after correction of each connecting screws.
『贰』 做样品的模具和做大货的模具,用英语分别该怎么说啊
做样品的模具：Make the mould of the sample
做大货的模具：Do big goods mould
『叁』 “模具”英文是怎么拼写的啊求...强求
mould 浇筑模具
die 冲压模具
progressive die 拉伸模具
『肆』 橡胶模具的英文怎么说
橡胶模具
英文翻译：rubbermould
[例句]Thestudyofarubbermould.
介绍了一种网格结构用橡胶模具的研究。
重点词汇释义：
橡胶：rubber; vulcanizate; latex
模具：mould; die; matrix; pattern die; pattern
『伍』 模具课 用英语怎么说
业界通常会分开来谈，五金模具叫：tooling
or
die
set
塑胶模具叫：mould
工厂的
模具课
部门叫：tooling/mould
department或tooling/mould
division
上模具课叫：have
a
tooling/mould
class
模具课程叫：tooling/mould
course
自己看著办吧!
『陆』 模具英语
‘undercut’是一个单词。
在焊接上称为‘咬边’，在伐木方面这个词系指砍树时现在树的根部侧面砍出一个契口，以便从树的另一边将树推倒，与此相同的词有：kerf、dip等。根据这几个词的汇总理解，在你的模具我方面建议译为侧边凹槽/侧凹槽。
不一定合适，请参考。
『柒』 模具英语，翻译成英文
3. Cutting down working procere and cost of labour force ：There is no need to polishing, processed moulds can be used into manufacturing directly. It can save labour force and increase efficiency.
『捌』 模具中的简易模用英语怎么说
简易模具：Simple Mold
single die 应该是：单冲模
『玖』 模具英文述语
模具述语
一、入水：gate
进入位： gate location
水口形式：gate type
大水口：edge gate
细水口：pin-point gate
水口大小：gate size
转水口： switching runner/gate
唧嘴口径： sprue diameter
二、流道: runner
热流道： hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴： hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头： connector plug
插座：connector socket
密封/封料：seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板： support plate
螺丝：screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）：mold base
上内模：cavity insert
下内模：core insert
行位（滑块）：slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
更多的情访问金比诺主页