模具里面的退针英语怎么说

⑴ 模具上的“行位”用英文怎么表达

Slide 行位,(总称)
Slide block 行位块(主体)
Slide insert 行位镶件,

另给些资料参照:

1． XXX！你现在有空吗，我可以问你一些问题吗？
Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a

question)?
2． 请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？
Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its

surface? Texture or Polishing?
3． 请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？
Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?
4． 这个产品的柱位我们打算做司筒。（或镶针）可以吗？
Can we add ejector sleeves or ejector pins in the boss of this part?
5． 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
There's an undercut at this position and it needs a slider. It will also have a parting line on

this side, is that OK?
6． 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？
We will make the lifter and (inner) slider in this position, will that be a problem?
7． 你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？
The 2D and 3D drawing you provided is not the same, can you tell me which one is correct?
8． 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自

己修改吗？修改后会给交给你确认。
There is no draft angle in the 3D drawing, some materials are too thick, and some place are too

thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after

we modify it.
9． 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的

产品图。
请确认你们的材料的缩水率是否正确？
Accoring to the shrinkage one over two hundred, the mold has been done in the right dimension, but

the part falls short to your part drawing, are you sure the shrinkage is right?
10． 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？
This position is too small and will make the steel material here too thin, can we widen it here?

11． 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？
The angular lifter interferes with the boss ring ejection. Please consider changing the position

of the boss.
12． 这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？
The rib here is too thin and on the high side, so it will be difficult to fill here when we do the

injection, can you inrcease the thickness of this rib?
13． 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两种做
法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？
Will you increase/decrease the material on this rib? We will use EDM if you add material, but there

are two option if you choose to decrease:1.Make inserts;2.Welding, because there is water in the

bottom of the insert, is that OK?
14． 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
This sample has been burned in the bottom because the venting is not good, we can add an insert in

the middle of the rib.
15． 重做镶件大约需要5-6天时间，你能接受吗？
It will take about 5 or 6 days to redo the insert, is that OK?
16． 产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。可能需要几天的时间

。
所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？
We have made the texture on this side, if we add material, it will take some days to remake the

texture by out-resourcing, so we suggest using the texture by EDM instead, is that OK?
17． 模具是用公制/英制的配件？需要备用件吗？
Is this mold dimension measured in inches or meters? Does it need spare parts?
18． 模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。
Will you provide the engraving content of the plate of this mold to us? When will you send it?
19． 可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大小、呵林柱尺寸、顶棍孔尺寸等
Can you provide the type of injection machine and other related information of this mold to us?

Such as the boss dimension, the hole's dimension of the ejector pin and the size of the injection

machine and so on.
20． 这个问题我需要同其它同事商议会再答复你。
I need to discuss this problem with the other colleagues and then I will reply back to you.

21． 我们将尽力达成你的计划，如有异常，会及时通知你。
We will try our best to complete your plan, if there are any complications, we will notify you

immediately.
22.这个产品的长度为330.12MM,宽度为78.96MM,高度为45MM.胶厚为2MM,重量为70.63g,试模注塑机型号为250吨,

胶料颜色为黑色,产品外表
面晒纹处理,内表面为抛光.需要日期章、环保章、材料章.前后模用2344氮硬，斜顶和行位座用738H，以上模具

信息正确吗？请确认！
"The length of this part is 330.12MM, Width is 78.96MM, height is 45MM, thickness is 2MM, weight is

70.63g, the injection machine is 250T,the material is black, the outside of the part has texture,

inner side needs polishing, and it also needs a date and recycle stamp,

the core&cavity is 2344 nitridng, the lifter and slider shelf is 728H. Please check the information

above!"
23． 现在到了吃午钣的时间，我们下午再继续好吗？
It is time to have lunch, let's discuss this project later this afternoon?
24.和滑块干涉的倒勾请加料填平至滑块可以顺利滑动
(The undercut area interferes with the slide block and needs to be filled with material to help the

slider move smoothly.)
25. 加肉太多 (The thickness added is too thick.)
26. 加肉面积太大 (The thickening area is too wide.)
27.GATE位置移位 ( The gate position is moved.)
28. 滑块拆的位置 (The split line of slide block or the area of slide.)
29. 此处有尖角，填充困难 (It is hard to fill this area e to the sharp feature.)
30. 此处钢材太薄，强度不足而且不容易冷却
(The strength of this area is too weak and it is hard to cool because the steel is too thin.)
31. 圆柱特徵要有一半圆不可以拆在滑块上，以免粘滑块造成拉白，拉断
(We avoid designing the semicircle of the cylinder on the slide block because it will be pulled

apart or cause drag marks.)
32. 此处做斜销在作动时会削到成品肉厚
(The part will be damaged if we make the lifter in this area.)
33. 这个面是装配面，不能加料
(This is a critical surface where we cannot add additional material.)
34. 此处料位太厚，会有缩水，建议减料改善
(Because of the shrinkage of the thickness, we suggest recing some wall thickness to improve it.)
35. 此面是不是外观面，此处做滑块的话会有夹线，是否可以接受
"(Please confirm whether it is a critical surface or not. Also, confirm whether it is acceptable to

have a slide
split line if we have a slide in this area. )"
36. 此处有倒勾，能否减料，使公母模靠破，不做滑块和斜销
"(Please confirm whether we can rece material to the area where we have an undercut as indicated

to have shut off
on cavity side. No slide block and lifter will be made. )"
37. 请尽快确认这种拆模方式和结构，否则会影响模期
(Please confirm the issues of Parting line, Gate position...Etc. as soon as possible; otherwise,

the lead-time will be extended.)
38. 此面是否有特殊要求，能否有顶针印
(Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.)
39. P.L面开在此处，模具上会有尖角和刀口，对模具寿命有影响
(There are sharp edges if we set the parting line here, It will rece the tool life)
40. 加大拔模角，以便脱模顺利 We suggest enlarging the draft angle to help release the tool.)

41. GATE做在此处的话有两个缺点：1.盖子打开时可以看到GATE的修剪部位; 2.两个斜销在同一侧，顶出也不是

很平衡.
(There are two problems if the gate is to be designed in this area:
a). It is easy to see the gate mark when you open the cap.
b). The ejectors are unbalanced when two lifters are on the same side)
42. GATE做在此处的话.盖子打开后看不到GATE的修剪部位
(The gate mark is not visible if the gate position is designed like this.)
43. 如果GATE一定要做在你们指定的位置的话，那还不如做在这一侧，这样的话还可以减小这个位置的缩水
"(If you insist that the gate position has to be like the original design, then we would further

recommend to have
it to the area indicated so it can avoid a shrink problem in this area.)"
44. 在此处GATE做潜顶针的话，背后的外观面会有冲料痕，而且成品又是黑色的，会最明显
(If the design of the gate has to be a sub. Gate, then the back surface of the part will have

serious flow marks e to the black colour.)
22. P.L开在此处不合理，模具加工困难，P.L应改为和图示的一样
"(This area is not suitable to have a Parting line because the tool will become more complicated;

therefore,
we recommend to have the Parting line as indicated.)"
45。产品粘母模的机会很大，能否在公模加倒勾，拉料顶针或者公模保留E.D.M纹，开模时使成品留在公模一侧
"(There is possible sticking on cavity; therefore, please confirm whether it can make undercuts,

snatch pins
or leave coarse E.D.M. on the core to snatch the part on) "
46.此处料厚段差很大，成品表面会有应力痕，是否接受
(Please confirm whether it is acceptable to have stress lines on the surface because the thickness

is not equal.)
47. 请注明何处为外观面，能否提供2D图和注意事项
(Please advise where the critical surface is. Please also provide us a 2D drawing with critical

dimensions. )
48. 红色所示处是有问题的地方，请特别注意
(Please note the red highlights because those areas have problems.)
49. 成品设计此处有问题，建议如下图所示修改
(We would suggest using the attached part design as the current design has problems.)
50. 此处改为一个球形的凹槽 (We suggest modifying it as a globe recess.)

51. 圆柱特征要有一半不可以拆在滑块里，以防拉断 (this issue is the same as no.8)
52. 此处大滑块上走小滑块，小滑块要先退，大滑块要做延迟
(The inside small slide block will recede first and the parent slide block have to postpone

sliding.)
53. 滑块要用液压油缸抽芯以保证开合模顺序
(The slide pins will use an oil cylinder to assure that the process is in proper order.)
54. 这个面有装配，加料的话装配时会顶住，如图所示
"(We cannot add material to this surface because it will intervene between the two parts when it is

assembled.
Please see the sketch attached. )"
55. 可降低斜销面，增加成品些许肉厚来做变化
(To descend the surface of lifter in order to thicken the part.)
56. 一半做斜销，一半做自然 (One half side will have the lifter and the other half will be

solid/nature.)
57. 此处两个柱子重叠，有倒勾，不能做自然，要做SLIDE
"(These two bosses are overlapping with undercut therefore it can not be made as solid. We
suggest making it with a slide block.)"
58. 此处强迫顶出 (This area needs force ejection.)
59. 公模两段开模，这个地方先退 (Here will be a double ejection for forward and receding.)
60. 此处做镶件会有夹线，能否接受 Please confirm whether it is acceptable that there will be a

split line here.)

61. 此面公母模1度靠破，会有段差，可否接受
(Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off

in Core / Cavity side.)
62. 这个尺寸能否加大 (Please confirm whether we can enlarge this dimension.)
63. 此处加一个凹槽，胶片的弹出效果会更好一些，试模后看装配的效果再做修正
"(It will affect the elastic of the film better if we add a recess. See how it will affect the

assembly parts,
and then make your decision.)"
64. 此处有倒勾，建议将剖面线所示部位CUT即可避免此处的倒勾
(There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an

undercut.)
65. 成型后SUB GATE要修平 (The gate (sub gate) needs to be trimmed evenly after being moulded.)
66. 此处倒勾先垂直顶出，之后再手动取出
(This area of the undercut needs to be ejected vertically, then taken out manually.)
67. 这两个面都有滑块，GATE改在此处改不到
(The gate is not suitable in this area becuase there are two sliding blocks sealing off this area.)
68. 此处加做一个旋转GATE，射出时方便调整成品的品质
(We would suggest placing a runner shut-off insert to adjust the volume of part filling.)
69. 此倒勾在滑块上强迫脱模，倒勾是否可以减小到0.6
(This undercut will be force ejected out, Please confirm whether it can be reced to 0.6 mm.)
70. 此柱子无法脱模，请确认是否是在转图时错位，能否提供客户的原始图档 data. )
(This boss is not releasable. Please check the file again and if possible, pleas re-send us the

original draft

71. 此柱子是实心的，会缩水 (This boss will shrink because it is a solid boss.)
72. 这个面是否要咬花，咬花番号是什麼，最小的拔模角要多大
(Please confirm whether this surface needs to be textured or not. Please advise texture specs.

Also, what's the min. draft. )
73. 这个面是否要打光，贴标签
(Please confirm whether this surface needs to be polished and stuck on a sticker.)
74. 红色显示的几个面拔模角太小，出模时会拉伤，建议加大拔模角
"(The red highlighted area has a problem of a small draft angle. We suggest enlarging the
draft to avoid casuing drag marks on the part.)"
75. 此RIB太薄，会填充不足 (This rib can not be filled properly because it is too thin.)
76. 此RIB太厚，会缩水 (This rib will have a shrink problem because it is too thick.)
77. 此处倒勾出模困难，建议先不做倒勾，成型后再二次加工，但要做治具，费用要另外算
(There are problems with this current design, we recommend doing this undercut as an alternative

but there will be additional costs.)
78. 柱子底部都要做火山口
(The base of all bosses require a crater to avoid shrinkage.)
1.镶件，P.L.面有充足排气坑，P.L.面要开环形排气槽,并能将气体排到模外。
Insert/PL should have adequate venting,PL should have around slot for venting.
79.顶棍孔镶件端面距离底板面0,5mm,攻m20牙;
the surface of KO insert shound below bottom plate 0.5mm,thread M20.
80.回针，中托司与模胚部份避空0.5mm；
RP,EGP should have 0.5mm gap with the moldbase.
81.排气槽距封胶位10-15mm；
Venting slot distance from the seal off position 10-15mm
82.运水进用 E ，运水出用 S ；
Intake"E",Outtake"S"
83.底面板均要有隔热板,DME规格1/4厚；
Top/Bottom plate must have insulator plate,DME standard 1/4'H
84.吊环要在模具的重心（保证吊模时的平衡）;
Eyebolt should on the center of the mold(for balance)
85.吊模螺丝的位置要在前/后模部份的重心,保持平衡；
The eyebolt position on the cavity/core side should on the center of gravity for balance
86.唧嘴分试模唧嘴/走模唧嘴;
Sprue type:Trial/Delivery
87.喉塞选用：NPT规格;
Plug use NPT spec.
88.中托司采用HASCO滚珠形式.
Use HASCO ball EGP
89.水咀采用法国标准:1/4"的水咀写:RPL08-1151
Jiffy Use French Standard: 1/4" mark:RPL08-1151

All in English& Imperial Unit全部使用英文和英制单位
Are part dimensions to print plus shrink?请检查内模尺寸有否乘缩水?
All wires protected from sharp corners？凡有电线通过的角位要改为R角，是否完成？
All replaceable components must be standard components.所有替换的元件必须是标准件。
Add shot counter?是否加啤塑总计器？
A complicated mould with thorough design consideration to overcome the numerous design contraints.
一个复杂的模具，设计经过周详考虑，成功地克服了各种设计上的限制。
All moving components should use hardened steel : all slides should be installed with hardend or

lubricated alloy wear plates and gibs, and with positive slide retainer.
所有移动的零件应使用硬钢料，行位必须用硬垫板和硬线条，而且必须有限位及定位锁。

BOM including water fittings,ejectors&custom components.BOM的内容应包含运水接头,顶针和自制的零件.
BeCu for lifters if w/o water circuits。若没有运水回路，斜顶为铍铜。

Corresponding components mirrored at core&cavity对应的部件在前、后模平面视图中镜像
Check polish for line of draw finish？有否省光就出模?
Core pull slot mechanism installed and O.K.
Crane capacity and loading clearance.模具须用多大吊机才可搬动。
Conct moldflow &mold warp analysis.经流道及变形电脑模拟分析。
Component and/or 3D mould design drawing.散件图或3D模具图
Cooling less important when dimensions are not important.若尺寸不重要，适量冷却也可。
Combine a traditional 4 cavity edge gate and a 4 cavities reverse gate mould which help to double

the moulding capacity and rece proction cost.
将一个标准四模腔大水口模具与一个四模腔倒转大水口模具结合成为一套可于同一大小的注塑机，生产量可增加

一倍的层板模具，并且可降低成本。
Can be seperated into two indivial moulds for moulding in two different mould shops.
此模具最大的特式是，可将模具分开变成两套，在不同地方生产，增加生产的灵活性。
Consists of all standard mould components which facilitates mould maintenance.
由于全套模具均利用模具标准零件制成，在维修及换零件上比较方便。

引用 报告 评分 回复 [广告] 免费【外贸招聘-外贸求职】？福步外贸职场地区论坛恭候你

Die draw called out出模方向的标示
Dimension all the opening , travel & clearance标出前、后模距离，滑动部件滑动距离和塑件脱离的位置
DME egr. Water fittings recessed and marked?是否使用DME运水接头及编号?
Delivery right side up , or in two halves？开箱后是否容易吊出模具及是否分开前/后模运输？
Eyebolt size and balance in 2 sides吊模孔尺寸，平衡，4边都要有
Ejection stroke & slide, lifter travel dimensioned出行程、行位、斜顶行程的标注。
Ejection study if lifter adopted若有斜顶，做出分析。
Ejection extended at the most顶出到极限位置
Ejector guide pins installation .顶针导柱的安装。
Eyebolts for inserts more than 50lbs.重量大于50lbs的镶件必须要有吊模孔。
Edge gate or sprue gate requiring secondary operation acceptable.边缘型或直入型水口都可以接受。

4 point in HRC different to lifters contacting or cavity steel。斜顶和与其接触的内模或镶件在硬度上

有4度的差别（HRC）。
4X size section , dimensioned to reflect the actual size.水口及水口顶针的4倍放大视图，按实际尺寸标

注。

General ,safety and handling 常规、安全和搬运要求
Guided ejection recommended for mould above 100 tons clamp capacity, ejector pins of 1.5mm or

smaller, or ejector stroke longer than 50mm.
建设模具用于锁模力超过100吨的注塑机，或有1.5mm以下的顶针或顶出行程超过50mm时，应装上顶针板导柱。
Guide pin cleared and vented?边钉插入模板有否顶着及加疏气空?

Hot manifold wired to print and checked? 热咀电线接位有否编号？
Horn pin clearance hole？斜边与行位有否空间？
Hydraulic actuated slide together with electrical limit switch.行位采用油压推动，配合安全电制。
Heaters fitted+0.002/-.000, leads tagged and connected to terminal.热嘴装配，电线源头、尾有否安装稳

固。（+0.002/.000）

Inserts keyed and numbered to prevent incorrect assembly.镶件定位和编号以防止不正确的组装。

Jaw angle 3 deg.more than angle pins(<25 degree).斜面角度要比行位斜边角度大3度(<25度)。

Keep enough space to run waterline at slide /lifter/major inserts.在行位、斜顶、主要镶件处保留足够

位置（空间）布置水槽。

Lifter angle less than 15 degree.斜顶角度小于15度。
Lifter rods dia, less than 1".斜顶杆直径不能少于1"。
Limit switch in tact and protected.是否已安装限位制？

⑵ 模具司筒顶针回不到位，左右两边就一面有是怎么回事啊！

这个问题还是要哥来回答你，要是你确定是司筒而不是司筒针的话，
你说的这个情况有可能是以下几个问题
，
1，顶针板沉头过深（看你追问的内容，应该是检查过的，可以排除）
2，司筒和模仁配合不顺，加热之后就紧了，以致顶针板回不到位，但是这个问题会导致其他的顶针也会回不到位，还有只有在回针短了才会出现这个情况，要不然回针是可以压回去的。这个你可以再确认一下。要是只有司筒高起来，就要看看顶针板司筒前面承靠面是不是太少，你的司筒挂台是不是磨过定位，使得杯头过小。这样司筒不顺的时候，司筒挂台前面陷下去了。要是是好的，那就不可能，除非司筒高度不对。或者是司筒被拉长了。哈哈
3，你的司筒配合的是入子，入子背后承靠面太小，入子后退了，这个你也要确认一下。
4，你说的”就像退不到位一样，毛边就出来了“，就这句话来看，你没有去测量产品的柱子是不是短了两个毫米，这种开始两模好的，后面就是毛边的还有一种情况就是司筒针退了，使得司筒针的台阶低于司筒，这样也会出现毛边一样的东西，这个要确认司筒针压板螺栓能不能锁到底，还有螺丝够不够大，要是针比较大的话，是要两端锁螺丝的。要是针比较小而且长的话，就要想办法加托，做有托司筒和针。如果针是靠破的话，你要看看长度对不对，预压是不是太多了
基本的可能性，我都分析到了，应该能解决你的问题，要是还不能，很有可能你的问题没表达清楚。请发产品柱子照片给我看看。
十二年钳工手打，请及时采纳~

⑶ 模具术语

我怎么一个都没听说过。
好像是从外文直译过来的。你能不能把外文原文贴上来

⑷ 模具回针是什么

模具回针是模具合模时让前模顶回顶针板而设置的顶杆。

模具，工业生产上用以注塑、吹塑、挤出、压铸或锻压成型、冶炼、冲压等方法得到所需产品的各种模子和工具。

简而言之，模具是用来制作成型物品的工具，这种工具由各种零件构成，不同的模具由不同的零件构成。它主要通过所成型材料物理状态的改变来实现物品外形的加工。素有“工业之母”的称号。

在外力作用下使坯料成为有特定形状和尺寸的制件的工具。广泛用于冲裁、模锻、冷镦、挤压、粉末冶金件压制、压力铸造，以及工程塑料、橡胶、陶瓷等制品的压塑或注塑的成形加工中。模具具有特定的轮廓或内腔形状，应用具有刃口的轮廓形状可以使坯料按轮廓线形状发生分离（冲裁）。

(4)模具里面的退针英语怎么说扩展阅读

模具选材需要满足三个原则，模具满足耐磨性、强韧性等工作需求，模具满足工艺要求，同时模具应满足经济适用性。

耐磨性，坯料在模具型腔中塑性变性时，沿型腔表面既流动又滑动，使型腔表面与坯料间产生剧烈的摩擦，从而导致模具因磨损而失效。所以材料的耐磨性是模具最基本、最重要的性能之一。

硬度是影响耐磨性的主要因素。一般情况下，模具零件的硬度越高，磨损量越小，耐磨性也越好。另外，耐磨性还与材料中碳化物的种类、数量、形态、大小及分布有关。

强韧性，模具的工作条件大多十分恶劣，有些常承受较大的冲击负荷，从而导致脆性断裂。为防止模具零件在工作时突然脆断，模具要具有较高的强度和韧性。模具的韧性主要取决于材料的含碳量、晶粒度及组织状态。

⑸ 请各位高手提供点模具英语资料,谢谢~

landed plunger mold 有肩柱塞式模具

burnishing die 挤光模

landed positive mold 有肩全压式模具

button die 镶入式圆形凹模

loading shoe mold 料套式模具

center-gated mold 中心浇口式模具

loose detail mold 活零件模具

chill mold 冷硬用铸模

loose mold 活动式模具

clod hobbing 冷挤压制模

louvering die 百叶窗冲切模

composite dies 复合模具

manifold die 分歧管模具

counter punch 反凸模

molar mold 组合式模具

double stack mold 双层模具

multi-cavity mold 多模穴模具

electroformed mold 电铸成形模

multi-gate mold 复式浇口模具

expander die 扩径模

offswt bending die 双折冷弯模具

extrusion die 挤出模

palletizing die 叠层模

family mold 反套制品模具

plaster mold 石膏模

blank through dies 漏件式落料模

porous mold 通气性模具

plicated cavity plate 复板模

positive mold 全压式模具

fantail die 扇尾形模具

pressure die 压紧模

fishtail die 鱼尾形模具

profile die 轮廓模

flash mold 溢料式模具

progressive die 顺序模

gypsum mold 石膏铸模

protable mold 手提式模具

hot-runner mold 热流道模具

prototype mold 雏形试验模具

ingot mold 钢锭模

punching die 落料模

lancing die 切口模

raising(embossing) 压花起伏成形

re-entrant mold 倒角式模具

sectional die 拼合模
semi-positive mold 半全压式模具

shaper 定型模套

single cavity mold 单腔模具

solid forging die 整体锻模

split forging die 拼合锻模

split mold 双并式模具

sprueless mold 无注道残料模具

squeezing die 挤压模

stretch form die 拉伸成形模

sweeping mold 平刮铸模

swing die 振动模具

three plates mold 三片式模具

trimming die 切边模

unit mold 单元式模具

universal mold 通用模具

unscrewing mold 退扣式模具

yoke type die 轭型模

punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location 定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
模具术语中英文对照，全面、精选

第一期：
组装、冲压、喷漆等专业词汇

Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子
Pneumatic screw driver气动起子
worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板
barcode条形码
barcode scanner条形码扫描仪
fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造技术
cosmetic inspect外观检查
inner parts inspect内部检查
thumb screw大头螺丝
lbs.inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis |'∫æsi| 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS
电源电压接柆键
sheet metal parts 冲件
plastic parts塑料件
SOP制造作业程序
material check list物料检查表
work cell工作间
trolley台车
carton纸箱
sub-line支线
left fork叉车
personnel resource department
人力资源部
proction department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot机械手
hydraulic machine油压机
lathe车床
planer |'plein？|刨床
miller铣床
grinder磨床
driller钻床
linear cutting线切割
electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager |'depjuti| =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长
group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺

final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skræpid|报废
scrape ..v.刮;削
deficient purchase来料不良
manufacture procere制程
deficient manufacturing procere制程不良
oxidation |' ksi'dei？n|氧化
scratch刮伤
dents压痕
defective upsiding down抽芽不良
defective to staking铆合不良
embeded lump|in'bed| |l？mp|镶块
feeding is not in place送料不到位
stamping-missing漏冲
proction capacity生产力
ecation and training教育与训练
proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称
administration/general affairs dept总务部
automatic screwdriver电动启子
thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle蜂鸣器
defective proct label不良标签
identifying sheet list标示单
screwdriver holder起子插座
pedal踩踏板
stopper阻挡器
flow board流水板
hydraulic handjack油压板车
forklift叉车
pallet栈板
glove(s)手套
glove(s) with exposed fingers割手套
thumb大拇指
forefinger食指
midfinger中指
ring finger无名指
little finger小指
band-aid创可贴
iustrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头
sweeper扫把
mop拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain链条
jack升降机
proction line流水线
chain链条槽
magnetizer加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头

slipped screwhead/shippery screw thread滑手
speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise expansion projects企划
QC品管
die worker模工
proction, to proce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
culture教养
qualified procts, up-to-grade procts良品
defective procts, not up-to-grade procts不良品
waste废料
board看板
feeder送料机
sliding rack滑料架
defective proct box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料
to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
feature change 特性变更
evaluation评估
prepare for, make preparations for 准备
parameters参数
rotating speed, revolution转速
manufacture management制造管理
abnormal handling异常处理
proction unit生产单位
lots of proction生产批量
steel plate钢板
roll material卷料
manufacture procere制程
operation procere作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over切换
engineering, project difficulty工程瓶颈
stage die工程模
automation自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模

shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
vocabulary for stamping
冲压常词汇
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
reset复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivenry to. to send delinery back to retrn of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
common vocabulary for die engineering模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板

padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress proct在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验
description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点

difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished proct成品
semi-finished proct半成品
packing materials包材
good proct/accepted goods/ accepted parts/good parts良品
defective proct/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good procts良品
scraped procts报放心品
defective procts不良品
finished procts成品
disposed procts处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品

coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片
thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
inction感应
inction light感应光
response=reaction=interaction感应
ram连杆
edge finder巡边器
concave凸
convex凹
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金
magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式
voller pin formality滚针形式
cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
proction tempo生产进度现状
torque扭矩
spline=the multiple keys花键
quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的
moly high speed steel钼高速的
organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆

semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procere dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉
dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒
pin销
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块

⑹ 模具的core pins是什么意思

core pin: 心销 | 心型梢 | 中心销 | 穿孔杆

⑺ 公模/母模是male die/female die还是cavity/core 3Q~

流道: runner
热流道： hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴： hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头： connector plug
插座： connector socket
密封/封料： seal

二：模具零件： mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板： support plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch

三.模具成形不良用语英汉对照
aberration 色差
bank mark 料纹
bite 咬入
blacking hole 涂料孔(铸疵)
blacking scab 涂料疤
blister 起泡
blooming 起霜
low hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉
bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱
check 细裂痕
checking 龟裂
chipping 修整表面缺陷
clamp-off 铸件凹痕
collapse 塌陷
color mottle 色斑
corrosion 腐蚀
crack 裂痕
crazing 碎裂
crazing 龟裂
deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑
fissure 裂纹
flange wrinkle 凸缘起皱
flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕
haircrack 发裂
haze 雾度
incrustation 水锈
indentation 压痕
internal porosity 内部气孔
mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
orange peel 橘皮状表面缺陷
overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀
plate mark 模板印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹
resin wear 树脂脱落
riding 凹陷
sagging 松垂
saponification 皂化
scar 疤痕
scrap 废料
scrap jam 废料阻塞
scratch 刮伤/划痕
scuffing 深冲表面划伤
seam 裂痕
shock line 模口挤痕
short shot 充填不足
shrinkage pool 凹孔
sink mark 凹痕
skin inclusion 表皮折叠
straightening 矫直
streak 条状痕
surface check 表面裂痕
surface roughening 橘皮状表皮皱折
surging 波动
sweat out 冒汗
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹

各式模具分类用语英汉对照
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模
landed positive mold 有肩全压式模具
button die 镶入式圆形凹模
loading shoe mold 料套式模具
center-gated mold 中心浇口式模具
loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模
composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
molar mold 组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具
electroformed mold 电铸成形模
multi-gate mold 复式浇口模具
expander die 扩径模
offswt bending die 双折冷弯模具
extrusion die 挤出模
palletizing die 叠层模
family mold 反套制品模具
plaster mold 石膏模
blank through dies 漏件式落料模
porous mold 通气性模具
plicated cavity plate 复板模
positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具
progressive die 顺序模
gypsum mold 石膏铸模
protable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具
sectional die 拼合模
runless injection mold 无流道冷料模具
sectional die 对合模具
segment mold 组合模
semi-positive mold 半全压式模具
shaper 定型模套
single cavity mold 单腔模具
solid forging die 整体锻模
split forging die 拼合锻模
split mold 双并式模具
sprueless mold 无注道残料模具
squeezing die 挤压模
stretch form die 拉伸成形模
sweeping mold 平刮铸模
swing die 振动模具
three plates mold 三片式模具
trimming die 切边模
unit mold 单元式模具
universal mold 通用模具
unscrewing mold 退扣式模具
yoke type die 轭型模

机械类常用英语：冲压模具-零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location 定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块

机械类常用英语：冲压模具-模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板

冲压模具-冲压名称类英汉对照
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
extension dwg展开图
procere dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
gap间隙
punch wt.上模重量

⑻ 注塑机顶针退不到位怎么办

顶针退不到位有以下几种情况：
1.电子尺或解码器读数异常
2.顶针退确认的接近开关故障
3.顶针推板固定螺母松动导致顶退确认异常
4.顶针油缸缸体内有异物阻碍

⑼ 哪位老大可以帮忙翻译下模具专业英语

那模子二手的为压缩成型是机密的进入四之内基本类型, 即, 积极的模子, 拥有土地的积极模子, 闪光-类型模子, 和 semipositive 模子。

为了要变硬而且逐放热后可塑性的分开从那形成, 冷却会是必需品。

有七基本薄片形成程序: 整形，旋转, 磨, 演练、锯、提出、和研磨.(研磨剂机制)

在注入模子, 螺丝钉（螺杆）行为当做组合注射和 plasticizing 单位。

细工品的 physcal 作文非常影响力机制方法的选择、工具作文和几何学, 和那比率物质移动。

那定位力量一部机器有能力发挥是部份那大小指示和是标准的在吨中。

适当的一钢模的选择材料和一钢模制造业技术决定, 在很大程度上 , 锻链的有用生活一钢模。

在压缩成型中那塑料材料当做粉或运行是放置进入一之内热的钢模子洞。

引导者大头针, 或职位, 是展开在那低的鞋。

塑料时常包含其他的附加材料呼叫匈牙利货币单位。

当应用的时候那电的解除机制程序, 那材料被侵蚀电的结果解除在工具之间和工作。

部份制造被移动成型有更棒的力量, 更多制服密度，靠近的空间宽容, 和那分别线需要较少的清洁当做与部份相较制造被压缩成型。

那一钢模区段包含运动机制那一钢模和那插入物合并那投掷形式以便集会罐子是展开在那之间领带酒吧机器。

在早的破晓文明人类方面发现一热的块金属更容易槌打进入不同的之内形状。

工具必需品到农产品一给定的锻链不能够是制造直到那形状最后锻链有是坚决的。

固体模型除去电线的大部份的问题框架

韧化的这个程序有暖气那钢对一段明确的时间提高的温度和, 通常, 冷却它慢慢地。

式样是复制品那部份在制造但是有些微大的尺寸在团结期间考虑到收缩和冷却那投掷。

这类型的模子广泛地二手的因为构造比较容易和它控制厚度和密度在结束里面极限。 。

如果那表面异常地很难, 那切断速度在使第一个粗糙的上削减应该是减少适当地

焊接是一个程序在哪一个二材料,通常以金属复盖,经过本土化接合一起长备有接缝, 产生的从一个温度的适当组合, 压力和治金的情况。

⑽ 翻译英语，模具方面的

The EVA area pointed by arrow is too large, causing the rubber along its side to curl up