导航:首页 > 镀锌钢管 > 热镀锌发暗表面如何处理

热镀锌发暗表面如何处理

发布时间:2023-03-23 04:40:19

㈠ 客户有一批镀锌板表面不做任何处理,现在表面氧化有黑点,怎样才能去掉黑点,颜色又一致呢

表面黑点有2点可能:
1、由于漏镀原因造成的,就是说出现黑点的地方由于漏镀回,使铁离答子渗透出来发黑,这是显示了铁基体的颜色。修复方法:96%镀锌专用修复漆,先用砂纸打磨黑点部分,保证创口越小越好,再用镀锌漆修复,此漆修复后有锌层,专业人员可以指点修复方法。
2、由于镀锌板表面腐蚀导致的发黑,原因是你的客户镀锌板表面没有经过任何处理,这样的话如果在车间吊装、或者周围环境的影响遇到一些东西上面可能带有的酸,就会腐蚀镀锌板表面,腐蚀的表面经过空气的氧化很容易就会发黑,再经过湿润空气的腐蚀就能长出一层“白盐”,就是锌的碱式碳酸盐。这种发黑不能处理,如果打磨会导致大面积发黑,影响质量外观。

朋友如果你觉得回答的可以给个推荐,谢谢!

㈡ 热镀锌变色的处理

  1. 只有重新二抄次镀锌才可以。

  2. 热镀锌(galvanizing) 也叫热浸锌和热浸镀锌:是一种有效的金属防腐方式,主要用于各行业的金属结构设施上。是将除锈后的钢件浸入500℃左右融化的锌液中,使钢构件表面附着锌层,从而起到防腐的目的。

  3. 热镀锌工艺流程:成品酸洗-水洗-加助镀液-烘干-挂镀-冷却-药化-清洗-打磨-热镀锌完工。

㈢ 热镀锌板表面发黑为什么

热镀锌板表面发黑是白锈进一步氧化形成的。

白锈产生的原因主要有:

(1)钝化不良,钝化膜厚度不够或不均匀;

(2)表面未涂油或带钢表面残留水分;

(3)卷取时带钢表面含有水分;

(4)钝化未完全烘干;

(5)在运输或储存中受潮或雨水淋湿;

(6)成品存放时间过长;

(7)镀锌板与其他酸碱等腐蚀性介质接触或存放在一起。

成品在库中最长允许存放三个月,以避免存放过久产生氧化。

(3)热镀锌发暗表面如何处理扩展阅读

热镀锌板,将薄钢板浸入熔解的锌槽中,使其表面粘附一层锌的薄钢板。主要采用连续镀锌工艺生产,即把成卷的钢板连续浸在熔解有锌的镀槽中制成镀锌钢板;合金化镀锌钢板。这种钢板也是用热浸法制造,但在出槽后,立即把它加热到500℃左右,使其生成锌和铁的合金被膜。这种镀锌板具有良好的涂料的密着性和焊接性。

热镀锌按退火方式的不同可分为线内退火和线外退火两种类型,又分别叫保护气体法和熔剂法。

锌层脱落的主要原因有:表面氧化、有硅化合物、冷扎乳化液太脏、NOF段氧化气氛及保护气体露点太高、空燃比不合理、氢气流量偏低、炉子有氧渗入,带钢入锅温度偏低,RWP段炉压偏低及炉门吸风、NOF段炉温偏低,油脂蒸发不尽、锌锅铝含量偏低、机组速度太快、还原不充分、锌液中停留时间太短、镀层偏厚。

㈣ 我是做镀锌丝的,最近镀锌丝一直不亮,发灰还有斑点,是怎么回事希望同行或者技术人员能给点建议。急求

1)镀锌丝的原料;2)镀锌丝的原料前处理不稳定。

㈤ 热镀锌铁丝颜色不光亮,发黑发乌,怎么办

热镀锌产品颜色发黑发乌的因素大体可分为两大类,一方面工艺的问题,另一方面是材质的问题。这两大类的因素都可以通过添加合金,和调整工艺温度来得以控制。仅供参考。
中锌热浸镀

㈥ 镀锌时镀件凹洼处镀层不光亮、发暗是何原因如何解决

镀件的凹洼处都属于低电流区。此区发暗不光亮的原因主要和解决办法有以下几个专: 1)电流小。加属大电流至镀件边角上刚出现有气体析出为止。 2)溶液温度过高。用温度计测量时,一般镀液温度超过40。C后这种现象比较常见。有报道说,加入30.409/L氯化铵可改善。 3)镀液分散能力差。碱性镀锌溶液中火碱含量低,或氧化锌含量高。氯化钾镀锌时,氯化钾含量低都会出现这些毛病。 4)光亮剂不足。光亮剂不足时,也表现出低电流区不光亮。如果加光亮剂不见效:应*l,JJtl开缸剂。 5)杂质的影响。铅、铜、有机物杂质都会使低电流区不光亮。打霍尔槽片,使用总电流O.5A,镀lOmin后经水洗和硝酸出光,低电流区发棕色证明是铅。.黑色证明是铜,发白暗不光亮是有机杂质。前两种用锌纷处理,后一种打活性炭处理。

㈦ 请问镀锌钢管打磨亮了,过几天又会发乌怎么办

  1. 镀锌钢管打磨亮过几抄天又会发乌解决方法:

    对钢管表面进行处理(如涂一层沥青漆、环氧类漆或槽封),以隔绝介质与锌层的直接接触。

  2. 镀锌钢管在实际使用中很少有进行打磨的,因为镀锌的目的就是为了防止生锈,防止发乌。

  3. 镀锌钢管分为冷镀锌钢管、热镀锌钢管,冷镀锌钢管已被禁用,后者还被国家提倡暂时能使用。热镀锌钢管广泛应用于建筑、机械、煤矿、化工、铁道车辆、汽车工业、公路、桥梁、集装箱、体育设施、农业机械、石油机械、探矿机械等制造工业。

㈧ 镀锌板表面变黑了能还原吗

可以还原,找点稀盐酸或者稀硫酸的溶液洗一下.

㈨ 专业文章翻译:热浸镀锌层涂装前表面处理

Preparing Hot Dip Galvanizing for Painting – It’s not Overly Complicated

热浸镀锌层涂装前表面处理-这并不太复杂

文章来自防腐涂装良心网站KTAuniversity,原文链接  请点这里

Bare galvanizing provides excellent corrosion protection at a pH between 7 and 13, but corrosion of the zinc increases as the pH becomes more acidic (less than 7), or more alkaline (greater than 13).  When galvanizing is exposed to the lower or higher pH ranges, it should be painted.  Paint should also be applied when aesthetics is important, regardless of pH.  Unfortunately, when galvanizing is painted, paint failures can occur (Photo 1), but they are easy to prevent through proper surface preparation.

在 ph 值为7和13的情况下, 仅凭镀锌就可以提供优异的腐蚀保护, 但锌的腐蚀会稿侍随着 ph 值变酸性 (小于 7) 或碱性 (大于 13) 而提高。 当镀锌层暴露在更低或更高的 pH 值范围内时, 应当进行涂装。 当外观比较重要时, 无论 pH 值如何, 也应该涂装。 不幸的是, 对镀锌表面涂装时, 很可能发生涂层失效 (照片 1), 但通过适当的表面处理这很容坦斗易防止。

Photo 1 – Typical failure of paint to galvanizing e to lack of surface preparation.

照片 1-由于缺乏表面处理造成的典型涂层失效。

Surface preparation is the key to assuring successful coating adhesion and performance.  The extent of preparation required depends on the answers to these four questions:

Was the galvanizing passivated?

Is the galvanizing new?

Is the galvanizing partially weathered?

Is the galvanizing aged?

表面处理是保证涂层附着力和性能的关键。所需处理的程度取决于对以下四个问题的回答:

镀锌键信吵层钝化处理了吗?

镀锌层是新的吗?

镀锌层是否部分风化?

镀锌层是否老化?

Passivating Treatments – Passivation is a common practice used at the time of galvanizing to rece the formation of white storage stain.  Unfortunately, passivating treatments applied to galvanizing (especially chromate treatments) can interfere with the adhesion of coatings.  If the galvanized steel is going to be painted, the galvanizer should be notified in advance, so that the passivation step can be eliminated.  Frequently, however, parts have already been galvanized and the user does not know whether a treatment was applied.  When in doubt, the surface should be tested.  A suitable procere is provided in SSPC-SP16, Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals.”  Section 4.3.3 of the standard offers the following:

钝化处理  – 钝化是镀锌时常用的一种方法,以减少镀锌件储存时白锈印迹的形成。不幸的是,对镀锌件的钝化处理(特别是铬酸盐处理)会影响涂层的附着力。如果镀锌件要涂装,应提前通知镀锌人员,以便取消钝化步骤。然而,实际情况通常是部件已经镀锌完成但用户不知道是否进行了钝化处理。如有疑问,应对表面进行测试。SSPC - SP16中提供了一个合适的程序,即“涂装和未涂装镀锌件、不锈钢和有色金属表面的扫砂处理标准。” 该标准第4.3.3节规定如下:

If all three areas turn black immediately, there is no passivation on the surface. If the first area does not turn black within 10 seconds and the second and third areas turn black immediately, there is no passivation on the surface with the possible exception of light oil. If the first and second areas do not turn black within 10 seconds and the third area turns immediately, a passivator of some type is present.

If it is present, mechanical cleaning is typically required to remove it, although some of the etching/cleaning solutions discussed below suggest that they will also remove some treatments.  Before using them, it is recommended that the etching cleaner be applied to discrete areas followed by the testing described above to determine if the treatment is removed.  If the project schele permits, weathering of 12 to 18 months prior to painting, should also eliminate any treatment that may have been present.

如果3个区域均立刻变黑,则表面没有钝化处理。如果第1个区域没有在10秒内变黑,而第2和第3区域立即变黑,则表面没有钝化处理,但可能有轻微的油渍存在。如果第1和第2区域没有在10秒内变黑,而第3区域立即变黑,则表面有过钝化处理。

如果检测有过钝化处理,则通常需要机械工具来清理,尽管后面提到的一些蚀刻/清洗液也能去除某些钝化层。如果使用蚀刻清洗液,建议先在小块区域试验,随后进行上述测试,以确定是否去除了钝化层。如果项目进度允许,涂装前风化了12至18个月的构件也应去除可能存在的钝化层。

New and Partially Weathered Galvanizing – If the age of the galvanizing is less than approximately 48 hours, it may be possible to coat it as is, but if it is weathered between a couple days and approximately one year (termed partially weathered), surface preparation will be required.  Two methods that are commonly used to prepare the galvanizing are cleaning/etching with a phosphoric acid/detergent blend and abrasive blast cleaning.

Etching solutions are used to clean, ll, and roughen the surface for proper coating adhesion.  The solution is applied to the surface, typically scrubbed with a synthetic abrasive pad, thoroughly rinsed, and force dried.  Examples of solutions can be found in the Master Painters Institute (MPI) qualified procts list #25, Cleaner, Etching, for Galvanized Metal ( http://www.specifypaint.com/APL/paintinfo_APL_new/MpiNumber.asp?ID=25000 ).

新的和部分风化的镀锌层 –    如果镀锌时间小于约48小时,可以直接涂装,但如果镀锌层经过在几天至约一年之间的风化(称为部分风化),则需要进行表面处理。通常用于镀锌件的两种表面处理方法是喷砂清理和用磷酸/洗涤剂混合物进行清理/蚀刻。

蚀刻清洗液用于表面清理、表面暗化和粗糙化以获得适当的涂层附着力。将溶液施加到表面上,通常用合成研磨片研磨,彻底冲洗,并烘干干燥。溶液种类可在“Master Painters Institute ( MPI )”认证产品列表#25“镀锌金属的蚀刻清洗液”中找到。( http://www.specifypaint.com/APL/paintinfo_APL_new/MpiNumber.asp?ID=25000 )

Abrasive blast cleaning is performed according to SSPC-SP16.  Excerpts from a few paragraphs of the standard describing the cleaning of bare, uncoated metal (galvanizing) are repeated below.  The sentences that were redacted address the criteria for any paint remaining on the surface, which is not applicable to this article.

喷砂清理根据SSPC - SP16进行。以下是标准中描述清理裸露未涂装金属(已镀锌)的几段摘录。节略的部分是关于表面残留油漆的标准,不适用于本文因此省略。

Paragraph 4.3.1 of the standard requires the removal of wet storage stain by means other than blast cleaning since the “dwell time” required to remove it by blast cleaning can damage the galvanizing.  Other methods are addressed in a non-mandatory Appendix.  Appendix Section A3 indicates that salts from wet storage stain can be removed with a nylon brush and water, or a dilute solution of acetic or citric acid, lime juice, or white vinegar, followed by rinsing with a large amount of water.

Appendix Section A8.1 indicates that to rece the risk of damage, blast cleaning is done with relatively low nozzle pressures (A8.2) and a softer abrasive with a Mohs hardness of 5 or less (A8.1.1.).

Appendix Section A9 recommends that the thickness of the galvanizing be measured before blast cleaning and again after blast cleaning to confirm that it meets the specified thickness.  The thickness requirements may be found in the procurement documents, or as required in ASTM A123, Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Procts, or ASTM A153/153M, Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware.

The Appendix (A9.2) cautions that in the presence of moisture, zinc oxides can form quickly on the surface after preparation, so it should remain dry, and painted as soon as possible.  The same recommendations for a minimum 5°F (3°C) spread between surface temperature and dew point temperature when preparing steel (steel temperature being the higher of the two), also apply to galvanizing.

该标准第4.3.1段要求通过喷砂清理以外的方式清除储存时产生的白锈印迹,因为喷砂清理白锈印迹所需的“停留时间”可能会损坏镀锌层。其他方法在非强制性附录中讨论。附录部分A3指出,储存时产生的白锈印迹可以用尼龙刷和水,或乙酸或柠檬酸、柠檬汁或白醋的稀溶液除去,然后用大量水冲洗。

附录部分A8.1指出,为了降低锌层破坏风险,喷砂清理采用相对较低的喷嘴压力( A8.2 )和莫氏硬度为5或更低的较软磨料( A8.1.1 )。

附录A9建议在喷砂清理前和喷砂清理后测量镀锌层厚度,以确认其符合规定膜厚。厚度要求见采购文件,或ASTM A123《钢铁制品镀锌(热浸镀锌)标准规范》或ASTM A153/153M《钢铁五金件镀锌(热浸镀锌)规范》。

附录( A9.2 )警告称,在潮湿条件下,喷砂清理后会在表面会迅速形成锌氧化物,因此应保持干燥,并尽快涂装。与钢结构表面处理相同,镀锌层表面处理时同样建议表面温度超出露点温度至少5°F ( 3°C )。

Aged Galvanizing – When galvanizing has weathered for 12 to 18 months, the surface will have oxidized and can often be prepared for painting by pressure washing alone.  The key is to remove surface dirt and debris as well as zinc salts and confirm that the surface is ll (photo 2).

镀锌层老化  – 当镀锌层已经风化12至18个月时,表面将被氧化,并且通常只需要高压清洗处理就可以准备涂装。关键是清除表面污物和锌渣以及锌盐,并确认表面暗化(图2 )。

Photo 2 – Exterior surfaces of the galvanizing have weathered and can likely be painted after pressure washing to remove the salts, but note the lack of oxidation and the visible spangle in the in the protected area (red arrow).  A test patch should be applied to determine if the adhesion is adequate without roughening and lling the surface.

图2– 镀锌层的外表面已经风化,可以在高压清洗除去盐分后进行涂装。但请注意保护区(红色箭头)内氧化物不多,有可见亮色的金属锌,应在该区域小范围涂漆测试,以确定未粗糙暗化的表面涂料附着力是否足够。

Depending on the condition of the steel, 3,000 psi with a rotating tip may be adequate, but it’s best to apply a test patch of the coating after cleaning and check the adhesion to make certain.  If there is any doubt regarding the adhesion of the coating, either of the methods described above for partially weathered galvanizing (etching cleaner or SP-16 Brush-Off Blast) should be used.

根据钢材(表面高压冲水)的经验,旋转喷嘴的压力在3000psi(约20MPa)应该足够,但最好在锌层表面高压冲水后小范围涂漆测试,并检查附着力以确保合格。如果对涂层的附着力有任何疑问,则应使用上述部分风化后镀锌层的任一表面处理方法(蚀刻清洗液或SP-16扫砂)。

Conclusion – Most coating failures on galvanizing are the result of poor adhesion of the coating to the galvanizing.  Poor adhesion is typically caused by a lack of roughening of the smooth galvanizing, an abundance of zinc salts beneath the coating film, or the presence of a passivating treatment that inhibits adhesion of the coating. When properly prepared, coatings will adhere well to galvanizing and improve the aesthetics and corrosion protection afforded by the galvanizing.  This article described a few common methods or preparing galvanizing for painting.  Other methods are described in:

ASTM D6386, Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Proct and Hardware Surfaces for Painting

ASTM D7396, Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting

结论 – 镀锌过程中的大多数涂层失效是由于涂层与镀锌层的附着力差造成的。附着力差通常是由于光滑镀锌层的粗糙度不足、涂层下面锌盐的大量存在或抑制涂层粘附的钝化处理而引起的。经过适当的涂装前表面处理,涂层将很好地粘附到镀锌层上,并改善镀锌层的美观性和防腐性。本文介绍了几种常用的涂装前镀锌层表面处理方法。其他方法记录于如下标准:

ASTM D6386, 镀锌(热浸镀锌)钢铁制品和五金件涂装前表面处理的标准操作规程

ASTM D7396, 新的连续镀锌钢材涂装前表面处理的标准指南

原文作者介绍:

Ken Trimber is the President of KTA-Tator, Inc. He is Chairman of the SSPC Surface Preparation Committee and the SSPC Visual Standards Committee, as well as a member of the SSPC Standards Review Committee and ASTM DOl responsible for developing, reviewing and approving standards like the ones described in this article. He can be reached at [email protected]

ken Trimber,KTA-Tator公司的总裁,SSPC表面处理委员会和SSPC目视标准委员会主席,SSPC标准审查委员会和ASTM DOl成员,负责制定、审查和批准类似文中所述的标准。作者邮箱地址  [email protected]

㈩ 使用镀锌蓝白钝化剂钝化后工件膜层的颜色会逐渐变暗该怎么办

使用镀锌蓝白钝化剂钝化后,工件磨成的颜色会逐渐变暗的话,
你可以在上面喷一层漆就可以在一定程度上减小化学反应。然后延长变暗时间。

阅读全文

与热镀锌发暗表面如何处理相关的资料

热点内容
铁丝网怎么接护栏 浏览:975
13mm厚钢板止水带多少钱 浏览:803
安徽耐候钢板多少钱 浏览:344
地铁的用的是什么规格不锈钢 浏览:657
ysl方管125 浏览:401
钢材的疲劳破坏有什么特征 浏览:139
车架工具箱用什么材料焊接 浏览:455
圆钢筋是什么钢 浏览:480
锰的成分在钢板中起什么作用 浏览:773
DN42钢管外径是多少 浏览:279
焊接剂弄手上如何清洗 浏览:49
钢筋m8是什么意思 浏览:866
热镀锌方管全自动生产线 浏览:637
不锈钢0cr18ni9是什么意思 浏览:945
不锈钢门如何防锈去污 浏览:761
橡胶放模具如何最快 浏览:794
铝合金门和厨房门哪个好看 浏览:455
卫生间引线钢筋焊接如何计算 浏览:980
不锈钢与铜哪个怕水 浏览:463
大管怎么做弯头图 浏览:365